Rewaco RF1 GT Rebuild.
-
- Member
- Posts: 187
- Joined: Tue Dec 13, 2016 6:01 pm
- Location: Derbyshire
Re: Rewaco RF1 GT Rebuild.
You should be very proud of that Tiivp. Brilliant result and looks top dollar
-
- Member
- Posts: 103
- Joined: Wed Oct 05, 2016 9:04 pm
- Location: Near Belfast, N.Ireland
Re: Rewaco RF1 GT Rebuild.
Sounds like an error with Automatic Choke. Mine starts no bother and idles rich/slightly fast for about 30-45 sec then slows to normal idle.tiitvp wrote:jinjachin wrote:Not taking hours worked did you save much money against buy one
There is on problem that i cant get my head around.
When i first start engine (cold start) for a minute or so i cant touch throtthle if i run throtthle it will shoke and shuts down.
After a minut its ok and working fine.
If some rewaco owner reads this pleas let me know do you have same problem or you dont have it.
I think that it is somekind on sensor but witch one i to not know.
Because of that i try to learn about its custom ECU allsou, do get it diagnosted.
I can rev it though without cutting out, just choose not to if I can to let all get warmer before driving off.
If your not living life on the edge your taking up to much room
-
- Member
- Posts: 25
- Joined: Wed Mar 30, 2016 2:04 pm
Re: Rewaco RF1 GT Rebuild.
It seems todaly weird because it has only 5 sensors: T-map sensor, Crankshaft sensor, Throttle potentiometer and Lambda Sensor, water temp sensor.Baddon wrote:Sounds like an error with Automatic Choke. Mine starts no bother and idles rich/slightly fast for about 30-45 sec then slows to normal idle.tiitvp wrote:jinjachin wrote:Not taking hours worked did you save much money against buy one
There is on problem that i cant get my head around.
When i first start engine (cold start) for a minute or so i cant touch throtthle if i run throtthle it will shoke and shuts down.
After a minut its ok and working fine.
If some rewaco owner reads this pleas let me know do you have same problem or you dont have it.
I think that it is somekind on sensor but witch one i to not know.
Because of that i try to learn about its custom ECU allsou, do get it diagnosted.
I can rev it though without cutting out, just choose not to if I can to let all get warmer before driving off.
T-map and Throttle potentiometer i have allready replayst. Only possible by my eyes is water temp sensor?
I try to check that and next is diagnostic ecu(What seems to be dangerouse if you do no know what are you doing..
-
- Moved in and now we can't get rid
- Posts: 1009
- Joined: Sat Jun 25, 2011 11:36 pm
- Location: ayrshire
Re: Rewaco RF1 GT Rebuild.
lovely job.
-
- Member
- Posts: 25
- Joined: Wed Mar 30, 2016 2:04 pm
Re: Rewaco RF1 GT Rebuild.
Hi
Littlepit more information if someone needs it.
Radiator OLD Jeeps : Nissens 60986
Radiator vent : VA09-AP12/C-54S
As ventilator do not have code on it only companys name.
I searched from catalog and found one like needed.
Littlepit more information if someone needs it.
Radiator OLD Jeeps : Nissens 60986
Radiator vent : VA09-AP12/C-54S
As ventilator do not have code on it only companys name.
I searched from catalog and found one like needed.
-
- Moved in and now we can't get rid
- Posts: 3570
- Joined: Sun Jan 29, 2017 12:17 pm
- Location: Felixstowe
Re: Rewaco RF1 GT Rebuild.
A job well done'
I tried to be normal once, worst two minutes of my life.
Barry the cantankerous old goat.
Barry the cantankerous old goat.
-
- Part of the Furniture
- Posts: 204
- Joined: Thu Oct 11, 2018 8:28 am
Re: Rewaco RF1 GT Rebuild.
Is the mixture set correctly?When I first start engine (cold start) for a minute or so i cant touch throttle if i run throttle it will shake and shuts down.
Just seems symptomatic of rich and with choke closed it is just too rich to run.
-
- Newbie
- Posts: 2
- Joined: Mon Jan 30, 2023 12:56 am
Re: Rewaco RF1 GT Rebuild.
Hi
I don't suppose you remember what torque settings you used for the front fork assembly ?
I need the torque settings for all fork bolts
Aluminium block to stem top and bottom
Aluminium block to fork top and bottom
Front wheel nuts
I don't suppose you remember what torque settings you used for the front fork assembly ?
I need the torque settings for all fork bolts
Aluminium block to stem top and bottom
Aluminium block to fork top and bottom
Front wheel nuts
-
- Newbie
- Posts: 3
- Joined: Thu Sep 08, 2022 1:19 am
Re: Rewaco RF1 GT Rebuild.
Hi, You have done an awesome job, did you change the Steering head bearings?